MIDI trough Port-0' when i download the drivers for Linux from technical support page here: Ħ2&pid=215&cid=1 and i start to install the drivers i get also a error message, its not able to run hdjmod-dkms_1.28_all. there is no MIDI controler to choose from, the drop-down list for output is greyed and its not possible to open the drop-down list. At MIDI Through Port-0, when I check 'enable". When I start MIXXX in Ubuntu and open 'preferences' I have following settings: Audio Output: - Master: Hercules DJ Console RMX: USB Audio (hw:1,0) Channels 1-2 - Headphones: HDA Intel: ALC 269 Analog (hw:0,0) Channels 3-4 - Sample rate (hz) 48000 - Sound API: ALSA For Master I can choose: None, HDA Intel:ALC 269 Analog(hw:0,0), Hercules DJ Console RMX: USB Audio (hw:1,0), front, surround40, surround51, surround71, pulse, dmix, default For Headphones i can choose: None, HDA Intel:ALC 269 Analog(hw:0,0), Hercules DJ Console RMX: USB Audio (hw:1,0), front, surround40, surround51, surround71, pulse, dmix, default Latency: 21ms HERCULES DJ console RMX is not available via 'preferences->MIDI controllers'. But this stops after about 20 seconds with the final status: no button lights on - all off. Then all the blue lighted buttons begin to flash like a Christmas tree (lights go on and off). After a reboot I plugged in the HERCULES DJ Console RMX. 82801I (ICH Family) HD Audio Controller (rev03)) Operating System: Ubuntu 10.04 32-bit (must notice that I'm more a Ubuntu User than a Ubuntu/Linux expert) I 'downloaded" MiXXX 1.8 from the original homepage by executing the 3 steps explained here Ubuntu 10.04 (Lucid): Open a terminal, and enter: sudo add-apt-repository ppa:mixxxdevelopers/ppa sudo apt-get update sudo apt-get install mixxx libportaudio2 additional I installed the libdjconsole via synaptic. Audio Interface is a Realtek HD Audio (lspci says: AUDIO DEVICE: Intel Corp. Then play your stream in VLC to see what it sounds like. To mute Mixxxs local output, just turn the head-volume knob to zero. This Chiligreen Platin SE Notbook uses an Intel Celeron processor M743 (ULV 1.3 GHz, 1MB L2 Cache, 800 MHz), 3GB DDR RAM, Toshiba 500GB, Intel Graphics Media Accelerator (GMA) 4500M, 3x USB 2.0. A workaround is to set the Master output to 'None' in Preferences -> Sound Hardware and set your output device for the Headphones output. I'm using a Chiligreen Platin SE Notebook which should become my "AUDIO Source" then. So a colleague borrowed me his new HERCULES DJ Console RMX for a try out. Since my colleagues are switching to digital DJ-ing I'm also think about it. However, you can use third-party encoder plugins to stream to your SHOUTcast/Icecast server, such as AltaCast Standalone.Hi, First: Hello everybody, good evening! As my user name may even refer to, I'm completely new in this topic. Q: Shoutcast/Icecast streaming are available in DirEttore?Ī: Not directly. Stream to SHOUTcast and Icecast servers via Internet Broadcast plugin. Q: Shoutcast/Icecast streaming is available in PlayIt Live?Ī: Not directly. Internet DJ Console (Shoutcast & “Icecast”) However, you can use third-party encoder plugins to stream to your Shoutcast/Icecast server, such as ALTACAST. Q: Shoutcast/Icecast streaming is available in RadioDJ?Ī: Not directly. For commercial use, you will need to buy a commercial license. VirtualDJ Home is free for non-commercial use. Price: You can now download VirtualDJ Home for FREE.Virtual DJ Software (Shoutcast & “Icecast”) Some of those programs are Oddcast or WinAmp with the Shoutcast plugin. Anyway, it can be used along with other programs to broadcast an Internet station. ZaraStudio is not a program designed for that purpose, but it is a program that automates audio playback. Is ZaraStudio designed to broadcast an Internet station? To get the mic audio feed back into Mixxx, use a stereo 1/4' plug to 1/8' stereo adapter plugged into FX send and connect the 1/8' plug on the on the end into the microphone input of your USB mic/headphone adapter. Now plug your headset into the Mixer's headphone output and plug your microphone(s) into the mic input(s) on your mixer. In Mixxx - Preferences - Sound Hardware, click the input button and select the microphone you want to add - You can enter up to 4 microphones which are controllable from the Mixxx dashboard. You can talk over shows by yourself or with guests and control it all through your Mixxx setup. B) Click the Recording tab, click Microphone, and then click Properties. In the search box, type sound, and then click Sound. Once it is open go to Options>Preferences or simply press CTRL+P and Choose. A) Open Sound by clicking the Start button, and then clicking Control Panel. Do NOT use other versions of the LAME encoder or MIXXX will show an error. If that does not help then try to disable microphone using the below given steps. Hey Guys Luke here and today i am showing you a way that always works to get rid of static on your microphone:) hope you enjoy and remember to leave a like and subscribe for more videos, then.
0 Comments
Leave a Reply. |